Custom Rifles Eden Prairie MN
Looking for Custom Rifles in Eden Prairie? We have compiled a list of businesses and services around Eden Prairie that should help you with your search. We hope this page helps you find Custom Rifles in Eden Prairie.
4314 Shady Oak Road Min
Gunstopreloading Supplies Inc.(952) 474-0211
5667 Manitou Road
Magnum Research Inc218568806
3457 Veterans St
Rollands Guns & Sptg Gds612572869
28161 410Th St
31027 Front St
Pequot Lakes, MN
Pequot Lakes, MN
Territorial Gunsmiths(952) 931-9451
733 6th Avenue South
Ballistic Products, Inc.(763) 494-9237
20015 75th Ave N. Cor
Tate, Eugene S218564439
50503 615Th Ave
Eckelman, Mark P218829172
6866 10Th St
Fort Ripley, MN
Fort Ripley, MN
Viking Valley Hunt Club(218) 747-2121
36209 Co Hwy 126
A "Custom" Rifle on a Budget
Accuracy. What an incredible way to give yourself a true advantage.
Go to your club and get a bunch of guys together - and put a target out there at 250 meters. Break out the deer rifles and see who can shoot a decent group, even off of the bench, at this distance. I think you will be shocked at how few can do it.
So - with that in mind, I recently set out to try to develop a semi-custom rifle that I could afford and that would shoot - repeatedly - at MOA.
I started with a platform that I love - the Savage 10 with the Accutrigger.
Use any brand you like - this is not about name dropping. Almost all rifles, if you do your part, will shoot VERY well. The key is doing YOUR part.
At any rate, I started with a 10FP in .308... I chose this rifle because it is heavy and because, in this caliber, recoil is not bad. I dislike recoil and I think it leads to a LOT of accuracy problems.
Look at the macho guys with the 7 Mag's and the 300 WinMag's and see how they (generally) fare in the above mentioned shooting contest. These are great caliber rifles and very deadly in the hands of a "shooter" - but I have seen a lot of hunters who had these because of the caliber name and not because of the proven performance. A .243 in the hands of a good hunter is far more deadly than a 300 WinMag in the hands of someone who flinches.
The Accutrigger revolutionized factory triggers and now a lot of rifle manufacturers offer very good triggers. The Savage trigger is a true 3 lb trigger that breaks like a little tiny glass rod. A fine piece of engineering.
I purchased a Boyd's laminated thumbhole stock (no relation, unfortunately)... and it is a thing of beauty. I chose the thumbhole version because this design also helps to defray felt recoil but transmitting quite a bit of it into your thumb and palm. It makes a difference, for sure.
I cleaned the stock real well and then (after reading extensively) glass bedded the action into the stock. I will leave this process for another post but it is not nearly as hard or as complicated as you might think. This was my first glass bedding ever and I must say, it came out very well... both pieces fit very well and "snap" together like pieces of a puzzle. Using the correct torque values, I put the action screws in.
I added a Sims pad to the rear of the stock to further help reduce the felt recoil.
Using Leupold mounts and 30 mm rings, I then mounted the scope. In this case, I added a premium scope - the Meopta 3-12x56. While not cheap, these scopes are a joy to behold... again, this is not about names, you can use the glass and mounts of your preference. The rings are aligned and lapped and it is all put together, again, using the correct torque values.
I lean toward good glass - scopes and binoculars - in my opinion, buy once and cry once.
Then, it is off to the range for some fun!
The rifle is broken in following the manufacturers specifications and then I am down to se...